Paper Tayyari

Final Term PreparationFinal term ki tayyari

Questions from past final papers.Pichhle final papers ke sawal.

160 MCQs · 88 short · 26 long questions · 160 MCQs from past papers160 MCQs · 88 short · 26 long sawal · 160 MCQs past papers se

Start mock testMock test shuru karein
DoneHal kiye 0/160
– correctsahi
1.
★ Final term Spring 2011

In selective-reject ARQ, only the specific damaged or lost frame is __________.

  1. ARetransmitted
  2. BForwarded
  3. CSelected
  4. DRejected

Selective-reject resends only the frame that was damaged or lost.

2.
★ Final term Spring 2011

YMODEM has a __________ byte data unit.

  1. A1024
  2. B256
  3. C128
  4. D512

YMODEM uses 1024-byte data blocks (XMODEM uses 128).

3.
★ Final term Spring 2011

Which of the following sublayers resolves the contention for the shared media?

  1. AMAC
  2. BLLC
  3. CPhysical

The Media Access Control sublayer handles access to the shared medium.

4.
★ Final term Spring 2011

Like 10Base5, 10Base2 is a __________ topology LAN.

  1. ARing
  2. BMesh
  3. CStar
  4. DBus

Thick and thin Ethernet both use a bus topology.

5.
★ Final term Spring 2011

At the CRC generator, __________ added to the data unit after the division process.

  1. A0s are
  2. B1s are
  3. CThe polynomial
  4. DThe CRC remainder is

Zeros are appended before division; after division the remainder (CRC) replaces them.

6.
★ Final term Spring 2011

Flow control is needed to prevent __________.

  1. ABit errors
  2. BOverflow of the sender buffer
  3. COverflow of the receiver buffer
  4. DCollision between sender and receiver

Flow control stops the sender from overwhelming the receiver's buffer.

7.
★ Final term Spring 2011

In YMODEM, multiple files can be sent simultaneously.

  1. ATrue
  2. BFalse

YMODEM supports batch transfer of several files in one session.

8.
★ Final term Spring 2011

In 56K modems the maximum uploading speed is ______ and the downloading speed is ______.

  1. A40K, 56K
  2. B33.6K, 56K
  3. C56K, 33.6K
  4. DNone of given

56K modems are asymmetric: up to 33.6 Kbps upstream and 56 Kbps downstream.

9.
★ Final term Spring 2011

There are ________ basic categories of multiplexing.

  1. A3
  2. B4
  3. C2
  4. D5

The three are FDM, WDM and TDM.

10.
★ Final term Spring 2011

EIA-232 allows for a maximum bit rate of __________ Kbps.

  1. A40
  2. B30
  3. C20
  4. D10

EIA-232 is specified for up to 20 Kbps.

11.
★ Final term Spring 2011

In CRC, the quotient at the sender __________.

  1. ABecomes the dividend at the receiver
  2. BBecomes the divisor at the receiver
  3. CIs discarded
  4. DIs the remainder

Only the remainder is used; the quotient is thrown away.

12.
★ Final term Spring 2011

In line discipline, after the data transmission the sending system finishes with an __________ frame.

  1. AEOT
  2. BEKT
  3. CENT
  4. DESP

The sender ends the exchange with an EOT (end of transmission) frame.

13.
★ Final term Spring 2010

Traditional modems are widespread now at a data rate of __________.

  1. A56 Kbps
  2. B72 Kbps
  3. C42 Kbps
  4. D96 Kbps

The common traditional dial-up modem standard is 56 Kbps (V.90/V.92).

14.
★ Final term Spring 2010

A telephone network is an example of a __________ network.

  1. APacket-switched
  2. BCircuit-switched
  3. CMessage-switched
  4. Dnone of the given

The telephone network sets up a dedicated circuit for each call.

15.
★ Final term Spring 2010

In case of uploading, at the switching station data is converted to a digital signal using __________.

  1. ATCP
  2. BPCM
  3. CICP
  4. DTDM

The switching station digitizes the analog signal with pulse code modulation.

16.
★ Final term Spring 2010

Category 5 UTP cable is used for data transmission of up to __________.

  1. A100 Mbps
  2. B200 Mbps
  3. C250 Mbps
  4. D400 Mbps

Cat 5 UTP supports data rates up to 100 Mbps.

17.
★ Final term Spring 2010

Which of the following primarily uses guided media?

  1. ACellular telephone system
  2. BLocal telephone system
  3. CSatellite communications
  4. DRadio broadcasting

The local telephone loop uses twisted-pair cable, a guided medium.

18.
★ Final term Spring 2010

Ultra high-frequency waves always use __________ propagation.

  1. AGround
  2. BSky
  3. CLine of Sight
  4. DSpace

UHF signals travel by line-of-sight propagation.

19.
★ Final term Spring 2010

Distortion occurs in a __________ signal.

  1. ARectified
  2. BComposite
  3. CAmplified
  4. Dnone of the given

Distortion arises because the frequency components of a composite signal travel at different speeds.

20.
★ Final term Spring 2010

Which of the following are not used to measure the performance of transmission media?

  1. AThroughput
  2. BPropagation Speed
  3. CPropagation Time
  4. Dnone of the given

Throughput, propagation speed and propagation time are all performance measures.

21.
★ Final term Spring 2010

A portion of the path that carries transmission between a given pair of devices is known as __________.

  1. ANode
  2. BBridge
  3. CChannel
  4. DGateway

A channel is the part of a link carrying one transmission between a device pair.

22.
★ Final term Spring 2010

__________ takes data from one high-speed line and breaks it into portions.

  1. AMultiplexing
  2. BInverse multiplexing
  3. CInverse subtraction
  4. DInverse addition

Inverse multiplexing splits one high-speed stream over several lower-speed lines.

23.
★ Final term Spring 2010

In primary-secondary communication, the __________ is always the initiator of a session.

  1. APrimary
  2. BSecondary
  3. CSender
  4. DReceiver

In poll/select line discipline the primary device always starts the exchange.

24.
★ Final term Spring 2010

__________ coordinates the amount of data that can be sent before receiving acknowledgment.

  1. Aflow control
  2. Berror control
  3. Cdata control

Flow control limits how much data the sender may send before an ACK.

25.
★ Final term Spring 2010

If the ASCII character H is sent and the character I is received, what type of error is this?

  1. ASingle-bit
  2. BMultiple-bit
  3. CBurst
  4. DRecoverable

H = 1001000 and I = 1001001 differ in only one bit.

26.
★ Final term Spring 2010

In __________ ARQ, if a NAK is received, only the specific damaged or lost frame is retransmitted.

  1. AStop-and-wait
  2. BGo-Back-N
  3. CSelective reject
  4. DStop-and-wait & Go-back-N

Selective-reject resends only the frame named in the NAK.

27.
★ Final term Spring 2010

Data link protocols can be divided into __________ sub-groups.

  1. Atwo
  2. Bthree
  3. Cfour
  4. Dfive

Data link protocols are either asynchronous or synchronous.

28.
★ Final term Spring 2010

If odd parity is used for ASCII error detection, the number of 0s per 8-bit symbol is __________.

  1. AEven
  2. BOdd
  3. CIndeterminate
  4. D42

With an odd number of 1s in 8 bits, the number of 0s (8 minus odd) is also odd.

29.
★ Final term Spring 2010

The (LLC) PDU has no flag fields, no CRC, and no station address.

  1. ATrue
  2. BFalse

The IEEE 802.2 LLC PDU has only SAP addresses and control; framing and CRC are in the MAC frame.

30.
★ Final term Spring 2010

The checksum method is used for __________ layers.

  1. APhysical
  2. BApplication
  3. CTransport
  4. DData link

The Internet checksum is used by upper-layer protocols such as TCP/UDP, while the data link layer uses CRC.

31.
★ Final term Spring 2010

A repeater is an amplifier, not a regenerator.

  1. ATrue
  2. BFalse

A repeater regenerates the original bit pattern rather than amplifying noise.

32.
★ Final term Spring 2010

RARP stands for Reverse Address Resolution Protocol.

  1. ATrue
  2. BFalse

RARP is the Reverse Address Resolution Protocol, mapping physical to logical address.

33.
★ Final term Spring 2010

The BNC-T connector is a T-shaped device with _______ ports.

  1. AThree
  2. BTwo
  3. CFour
  4. DFive

A BNC-T has three ports: two for the cable and one for the NIC.

34.
★ Final term Spring 2010

A periodic signal completes one cycle in 0.001 s. What is the frequency?

  1. A1 Hz
  2. B100 Hz
  3. C1 KHz
  4. D1 MHz

f = 1/T = 1/0.001 s = 1000 Hz = 1 kHz.

35.
★ Final term Spring 2010

Zero-crossing bandwidth is also called equivalent noise bandwidth.

  1. ATrue
  2. BFalse

Zero-crossing bandwidth and equivalent noise bandwidth are different bandwidth definitions.

36.
★ Final term Spring 2010

If FCC regulations are followed, the carrier frequencies of adjacent AM radio stations are __________ apart.

  1. A5 KHz
  2. B10 KHz
  3. C200 KHz
  4. D530 KHz

Each AM station gets a 10 kHz band.

37.
★ Final term Spring 2010

There are __________ types of serial transmission.

  1. A1
  2. B2
  3. C3
  4. D4

Serial transmission is either asynchronous or synchronous.

38.
★ Final term Spring 2010

Which of the following is an example of ITU-T modem standards?

  1. AT-series
  2. BX-series
  3. CN-series
  4. DV-series

ITU-T modem standards are the V-series (e.g. V.32, V.90).

39.
★ Final term Spring 2010

In 56K modems, the maximum data rate in the uploading direction is still __________.

  1. A26.6 Kbps
  2. B33.6 Kbps
  3. C36.6 Kbps
  4. D46.6 Kbps

Upstream a 56K modem is limited to 33.6 Kbps.

40.
★ Final term Spring 2010

All popular fiber-optic connectors are __________ shaped.

  1. AConical
  2. BBarrel
  3. CCircular
  4. DRectangular

Popular fiber-optic connectors are barrel-shaped.

41.
★ Final term Spring 2010

The VLF and LF bands use __________ propagation for communications.

  1. AGround
  2. BSky
  3. CLine of sight
  4. DSpace

VLF and LF waves follow the earth's curvature by ground propagation.

42.
★ Final term Spring 2010

Multiplexing is the set of techniques that allows simultaneous transmission of multiple signals across a __________ data link.

  1. ASingle
  2. BMulti
  3. CSingle and Multi
  4. Dnone of the given

Multiplexing shares one link among several signals.

43.
★ Final term Spring 2010

The need for addressing makes asynchronous TDM inefficient for bit or byte __________.

  1. AInterleaving
  2. BAddition
  3. CSubtraction
  4. DNone of the given

Address overhead per slot makes asynchronous TDM wasteful for bit/byte interleaving.

44.
★ Final term Spring 2010

A traditional telephone line has a bandwidth of __________.

  1. A3000 Hz
  2. B4000 Hz
  3. C2000 MHz
  4. D4000 MHz

Voice lines pass about 300-3300 Hz, a bandwidth of 3000 Hz.

45.
★ Final term Spring 2010

Error control in the data link layer is based on __________.

  1. Aautomatic repeat request
  2. Bautomatic repeat acknowledgment
  3. Cautomatic send acknowledgment

Data link error control uses ARQ: retransmission of damaged or lost frames.

46.
★ Final term Spring 2010

In line discipline, the initiator first transmits a frame called an __________.

  1. AEnquiry
  2. BAcknowledgment
  3. CNAK
  4. DRequest

The initiator sends ENQ to ask if the receiver is ready.

47.
★ Final term Spring 2010

The primary device uses __________ to receive transmission from the secondary devices.

  1. AACK
  2. BENQ
  3. CPOLL

Polling is how the primary asks secondaries to send data.

48.
★ Final term Spring 2010

For stop-and-wait ARQ, for N data packets sent, __________ acknowledgments are needed.

  1. AN
  2. B2N
  3. CN-1
  4. DN+1

Each frame is acknowledged individually, so N frames need N ACKs.

49.
★ Final term Spring 2010

HDLC is an acronym for __________.

  1. AHigh-duplex line communication
  2. BHigh-level data link control
  3. CHalf-duplex digital link combination
  4. DHost double-level circuit

HDLC stands for High-level Data Link Control.

50.
★ Final term Spring 2010

Token Bus has no commercial application in data communications.

  1. ATrue
  2. BFalse

Token Bus (802.4) was used in factory automation, not commercial data networks.

51.
★ Final term Spring 2010

Each station in a Token Ring regenerates the frame.

  1. ATrue
  2. BFalse

Every Token Ring station acts as a repeater, regenerating the frame.

52.
★ Final term Spring 2010

A repeater works on the __________ layer.

  1. AData Link
  2. BPhysical
  3. CNetwork
  4. DApplication

A repeater only regenerates signals, a physical-layer function.

53.
★ Final term Spring 2010

The RG number gives us information about __________.

  1. ATwisted pairs
  2. BCoaxial cables
  3. COptical fibers
  4. Dall of the given

Coaxial cables are categorized by RG (radio government) ratings.

54.
★ Final term Spring 2010

The inner core of an optical fiber is __________ in composition.

  1. AGlass or plastic
  2. BCopper
  3. CBimetallic
  4. DLiquid

Fiber cores are made of glass or plastic.

55.
★ Final term Spring 2010

Which error detection method involves polynomials?

  1. AChecksum
  2. BTwo-dimensional parity check
  3. CCRC
  4. DSimple parity check

CRC treats data and divisor as polynomials.

56.
★ Final term Spring 2010

Which error detection method involves the use of parity bits?

  1. ASimple parity check & two-dimensional parity check
  2. BCRC
  3. CTwo-dimensional parity check
  4. DSimple parity check

Both simple and two-dimensional parity checks add parity bits.

57.
★ Final term Spring 2010

Which error detection method can detect a single-bit error?

  1. ASimple parity check
  2. BTwo-dimensional parity check
  3. CCRC
  4. DAll of the given

Parity, 2-D parity and CRC all detect any single-bit error.

58.
★ Final term Spring 2010

The Hamming code is a method of __________.

  1. AError detection
  2. BError correction
  3. CError encapsulation
  4. DError detection & Error encapsulation

Hamming code locates the erroneous bit so it can be corrected.

59.
★ Final term Spring 2010

Sliding window requires that data frames be transmitted __________.

  1. ASequentially
  2. BFrequently
  3. CSynchronously
  4. DAsynchronously

Sliding window numbers frames and sends them in sequence.

60.
★ Final term Spring 2010

IEEE divides the baseband category into ______ standards.

  1. A5
  2. B4
  3. C3
  4. D6

IEEE 802.3 baseband has five standards: 10Base5, 10Base2, 10Base-T, 1Base5 and 100Base-T.

61.
★ Final term Spring 2010

Which of the following ___________ uses a series of filters to decompose a multiplexed signal into its constituent signals?

  1. AMUX
  2. BDEMUX
  3. CSwitch
  4. DBridge

A demultiplexer uses filters to separate the combined signal back into its component signals.

62.
★ Final term Spring 2010

In Fast Ethernet, data rate can be increased by _______________ collisions.

  1. AIncreasing
  2. BDecreasing
  3. CKeeping Constant
  4. DNone of the given

Fewer collisions mean less wasted time on the medium, so effective data rate rises.

63.
★ Final term Spring 2009

In 4PSK each phase change represents ______ bits.

  1. A3
  2. B6
  3. C2
  4. D4

Four phases give log2(4) = 2 bits per phase change.

64.
★ Final term Spring 2009

When a beam of light travels through media of two different densities, if the angle of incidence is greater than the critical angle, ____________ occurs.

  1. AReflection
  2. BRefraction
  3. CIncidence
  4. DCriticism

Above the critical angle the light is totally reflected back into the denser medium.

65.
★ Final term Spring 2009

When we talk about unguided media, usually we are referring to _________.

  1. AMetallic wires
  2. BNonmetallic wires
  3. CThe air
  4. DWater

Unguided media transport signals through free space, usually the air.

66.
★ Final term Spring 2009

Optical fibers are defined by the ratio of the ___________ of their core to the diameter of their cladding.

  1. ADiameter
  2. BRadius
  3. CLength
  4. DWidth

Fiber types are named by core diameter to cladding diameter ratio, e.g. 62.5/125.

67.
★ Final term Spring 2009

Radio wave transmission utilizes ___________ different types of propagation.

  1. AFour
  2. BThree
  3. CTwo
  4. DFive

The course lists five types: surface, tropospheric, ionospheric, line-of-sight and space propagation.

68.
★ Final term Spring 2009

dB is ____________ if a signal is amplified.

  1. ANegative
  2. BPositive
  3. CNull
  4. DZero

Amplification makes P2 > P1, so 10 log10(P2/P1) is positive.

69.
★ Final term Spring 2009

A prism can deflect the light depending upon the angle of ____________ and the frequency.

  1. ADeviation
  2. BIncident
  3. CRefraction
  4. DReflection

A prism bends light according to its angle of incidence and its frequency.

70.
★ Final term Spring 2009

Asynchronous TDM is efficient only when the size of the time slot is kept relatively _______________

  1. ALarge
  2. BSmall
  3. CMedium
  4. DNone of the given

Each asynchronous TDM slot carries address overhead, so large slots keep that overhead proportionally small.

71.
★ Final term Spring 2009

The local loop has ___________ cable that connects the subscriber telephone to the nearest end office.

  1. ATwisted-pair
  2. BCoaxial
  3. CFiber-optic
  4. DNone of the given

The local loop is a twisted-pair line from the subscriber to the end office.

72.
★ Final term Spring 2009

Data from a computer are ____________; the local loop handles _________ signals.

  1. AAnalog; analog
  2. BAnalog; digital
  3. CDigital; digital
  4. DDigital; analog

Computers produce digital data while the traditional local loop carries analog signals, hence modems.

73.
★ Final term Spring 2009

Which error detection method uses ones complement arithmetic?

  1. ASimple parity check
  2. BTwo-dimensional parity check
  3. CCRC
  4. DChecksum

The checksum adds segments in ones complement arithmetic and complements the sum.

74.
★ Final term Spring 2009

Error control is both error _________ and error ___________

  1. Adetection; correction
  2. Bdetection; deletion
  3. Cdetection; avoidance
  4. Ddetection; forwarding

Error control covers detecting errors and correcting them, usually by retransmission.

75.
★ Final term Spring 2009

Addressing is not needed in _______________ configuration.

  1. APoint to Point
  2. BMultipoint
  3. CPoint to point and multipoint

With only two devices on a point-to-point link there is no need to identify the receiver.

76.
★ Final term Spring 2009

In a Go-Back-N ARQ, if the window size is 63, what is the range of sequence numbers?

  1. A0 to 63
  2. B0 to 64
  3. C1 to 63
  4. D1 to 64

Window size 2^m - 1 = 63 gives m = 6, so sequence numbers run 0 to 63.

77.
★ Final term Spring 2009

A timer is set when ___________ is sent out.

  1. AA data frame
  2. BAn ACK
  3. CA NAK

The sender starts a timer for each data frame so it can retransmit if no acknowledgment arrives.

78.
★ Final term Spring 2009

BLAST stands for:

  1. ABlocked asynchronous transmission
  2. BBlocked synchronous transmission
  3. CBarrel asynchronous transmission
  4. DBelow asynchronous transmission

BLAST is Blocked Asynchronous Transmission.

79.
★ Final term Spring 2009

The HDLC ___________ field defines the beginning and end of a frame.

  1. AFlag
  2. BAddress
  3. CControl
  4. DFCS

The 01111110 flag marks the start and end of an HDLC frame.

80.
★ Final term Spring 2009

_________ is the access protocol used by traditional Ethernet.

  1. ACSMA/CD
  2. BCSMA/CA
  3. CToken Ring
  4. DCSMA

Traditional Ethernet uses CSMA/CD.

81.
★ Final term Spring 2009

Bridges can divide a large ________ into smaller segments.

  1. ANetwork
  2. BPacket
  3. CFrame
  4. DAddress

Bridges split a large network into smaller segments to isolate traffic.

82.
★ Final term Spring 2009

Like VRC, LRC and CRC, checksum is also based on _______________.

  1. ARedundancy
  2. BDecimal Division
  3. CEncryption
  4. DEncoding

All these error-detection methods add redundant bits to the data.

83.
★ Final term Fall 2009

Data must be converted into __________ before transmission.

  1. Asignal
  2. Bwave
  3. Celectric pulse

Data must be transformed into signals to travel over a medium.

84.
★ Final term Fall 2009

A parabolic dish antenna is a(n) ______________ antenna.

  1. AOmnidirectional
  2. BBidirectional
  3. CUnidirectional
  4. DHorn

A parabolic dish focuses signals in a single direction.

85.
★ Final term Fall 2009

Which multiplexing technique involves signals composed of light beams?

  1. AFDM
  2. BTDM
  3. CWDM
  4. Dnone of the given

Wavelength-division multiplexing combines light signals of different wavelengths.

86.
★ Final term Fall 2009

Multiplexing has long been used as an essential tool in the ____________.

  1. AElectronic industry
  2. BTelephone industry
  3. CSpace science
  4. DVLAN

Telephone companies have long multiplexed many calls over shared links.

87.
★ Final term Fall 2009

In CRC there is no error if the remainder at the receiver is ____________

  1. AEqual to the remainder at the sender
  2. BZero
  3. CNonzero
  4. DThe quotient at the sender

A zero remainder at the checker means the data unit is accepted.

88.
★ Final term Fall 2009

Which error detection method can detect a burst error?

  1. AThe parity check
  2. BTwo-dimensional parity check
  3. CCRC
  4. DTwo-dimensional parity check and CRC

Both two-dimensional parity and CRC can detect burst errors; simple parity cannot reliably.

89.
★ Final term Fall 2009

At the CRC checker, ________ means that the data unit is damaged.

  1. AA string of 0s
  2. BA string of 1s
  3. CA string of alternating 1s and 0s
  4. DA nonzero remainder

Any nonzero remainder at the checker indicates an error.

90.
★ Final term Fall 2009

XMODEM is a ______________ protocol designed for telephone-line communication between PCs.

  1. Afile transfer
  2. Bhardware
  3. Csoftware
  4. Dapplication exchange

XMODEM is a half-duplex stop-and-wait file transfer protocol.

91.
★ Final term Fall 2009

Which of the following combines features of the other two?

  1. AZMODEM
  2. BYMODEM
  3. CXMODEM
  4. DNone of given

ZMODEM combines features of XMODEM and YMODEM.

92.
★ Final term Fall 2009

Which one of the following uses full-duplex operation with sliding window flow control?

  1. ABLAST
  2. BXMODEM
  3. CYMODEM
  4. DZMODEM

BLAST is full duplex with sliding window flow control, unlike the stop-and-wait MODEM protocols.

93.
★ Final term Fall 2009

The DSAP and SSAP are addresses used by _________ to identify the protocol stacks.

  1. ALLC
  2. BMAC
  3. CNetwork

DSAP and SSAP in the LLC PDU identify the upper-layer protocols.

94.
★ Final term Fall 2009

Which of the following is a bus topology LAN that uses baseband signaling and has a maximum segment length of 500 meters?

  1. A10Base5
  2. B10Base2
  3. C100Base2
  4. D100Base5

10Base5 (thick Ethernet) is a baseband bus with 500 m segments.

95.
★ Final term Fall 2009

When a collision is detected in a network using CSMA/CD, _________

  1. AThe frame is immediately resent
  2. BA jam signal is sent by the station
  3. CThe backoff value is set to 0
  4. DThe backoff value is decremented by 1

On detecting a collision the station sends a jam signal so all stations know about it.

96.
★ Final term Fall 2009

When systems share a point-to-point link, the protocols used are called ___________ protocols.

  1. ADirect
  2. BIndirect
  3. CMonolithic
  4. Dstructured

Communication over a dedicated point-to-point link uses direct protocols.

97.
★ Final term Fall 2009

An unauthorized user is a network ___________ issue.

  1. APerformance
  2. BReliability
  3. CSecurity
  4. DAll of the given

Protecting against unauthorized access is a security concern.

98.
★ Final term Fall 2009

Physical layer defines characteristics of interface between device and _________

  1. Atransmission medium
  2. Banother device
  3. Canother peer physical layer at other side
  4. Dmodem

The physical layer specifies the interface between devices and the transmission medium.

99.
★ Final term Fall 2009

________ layer deals with syntax and semantics of information exchange.

  1. Apresentation
  2. Bsession
  3. Capplication
  4. Dphysical

The presentation layer handles the syntax and semantics of exchanged information.

100.
★ Final term Fall 2009

To allow access to network resources is the function of ___________

  1. Aapplication layer
  2. Bphysical layer
  3. Cnetwork layer

The application layer gives users access to network resources.

101.
★ Final term Fall 2009

EIA-449 provides much better functionality than EIA-________

  1. A232
  2. B223
  3. C262
  4. D222

EIA-449 was designed to improve on the speed and distance limits of EIA-232.

102.
★ Final term Fall 2009

The _________ is an association that sponsors the use of infrared waves.

  1. AIrDA
  2. BEIA
  3. CFCC
  4. DPUD

The Infrared Data Association (IrDA) promotes infrared communication.

103.
★ Final term Fall 2009

The section of EM spectrum defined as Radio Communication is divided into _____ ranges called BANDS.

  1. A8
  2. B10
  3. C5
  4. D6

Radio communication (3 kHz-300 GHz) is split into eight bands, VLF through EHF.

104.
★ Final term Fall 2009

In __________ propagation, low-frequency radio waves hug the earth.

  1. AGround
  2. BSky
  3. CLine of Sight
  4. DSpace

In ground propagation low-frequency waves travel close to and follow the earth's surface.

105.
★ Final term Fall 2009

In bit ____________, MUX adds extra bits to a device.

  1. AStuffing
  2. BAdding
  3. CMultiplication
  4. DExchanging

Bit stuffing (pulse stuffing) adds dummy bits so a slower source matches the TDM slot rate.

106.
★ Final term Fall 2009

FTTC stands for _____________

  1. Aflexible to the curb
  2. Bfiber to the curb
  3. Cfiber to the cable
  4. Dfiber to the center

FTTC means fiber to the curb.

107.
★ Final term Fall 2009

In data link layer, communication requires at least ___________ devices working together.

  1. A3
  2. B2
  3. C4
  4. D5

Data link communication needs at least a sender and a receiver.

108.
★ Final term Fall 2009

Data link control is composed of ____________ important functions.

  1. A2
  2. B3
  3. C4
  4. D5

The three functions are line discipline, flow control and error control.

109.
★ Final term Fall 2009

YMODEM uses ITU-T CRC-_____ for error checking.

  1. A16
  2. B32
  3. C8
  4. D4

YMODEM replaced XMODEM's checksum with ITU-T CRC-16.

110.
★ Final term Fall 2009

What is present in all HDLC control fields?

  1. AP/F bit
  2. BN(R)
  3. CN(S)
  4. DCode bits

I, S and U frame control fields all contain the poll/final bit.

111.
★ Final term Fall 2009

In FDDI, token passing is used as access method.

  1. ATrue
  2. BFalse

FDDI uses token passing on a dual fiber ring.

112.
★ Final term Spring 2009

Headers are added at layers 1 and 7 of OSI model.

  1. ATrue
  2. BFalse

Headers are added at layers 6 to 2, not at the physical layer.

113.
★ Final term Spring 2009

Transmission media are usually categorized as _____________

  1. AFixed or Unfixed
  2. BGuided or Unguided
  3. CDeterminate or Indeterminate
  4. DMetallic or Nonmetallic

Media are classed as guided (cables) or unguided (wireless).

114.
★ Final term Spring 2009

Radio wave and microwave frequencies range from _________.

  1. A3 to 300 KHz
  2. B300 KHz to 300GHz
  3. C3 KHz to 300 GHz
  4. D3 KHz to 3000 GHz

The radio communication spectrum spans VLF (3 kHz) to EHF (300 GHz).

115.
★ Final term Spring 2009

In ______________ method a signal can be directed in a straight line from antenna to antenna.

  1. ALine of sight
  2. BGround propagation
  3. CSky propagation
  4. DMicrowaves

Line-of-sight propagation sends very high frequency signals straight between antennas.

116.
★ Final term Spring 2009

If a T-1 carries 8000 frames, the data rate is ___________

  1. A2.544 Mbps
  2. B1.544 Mbps
  3. C1.544 Kbps
  4. D1.544 Gbps

8000 frames/s x 193 bits per frame = 1.544 Mbps.

117.
★ Final term Spring 2009

Optical signals are multiplexed using _________ at switching office to create wider BW optical signals.

  1. AWDM
  2. BFDM
  3. CTDM
  4. DMUX

Wavelength division multiplexing combines light signals on a fiber.

118.
★ Final term Spring 2009

Which error detection method consists of a parity bit for each unit as well as an entire data unit of parity bits?

  1. ASimple parity check
  2. BTwo-dimensional parity check
  3. CCRC
  4. DChecksum

Two-dimensional parity adds a parity bit per unit plus a row of column parity bits.

119.
★ Final term Spring 2009

ENQ/ACK stands for ______________

  1. AEnquiry/ Acknowledgment
  2. BEnque/ Acknowledgment
  3. CEnquist/ Acknowledgment
  4. Dnone of the given

ENQ is enquiry and ACK is acknowledgment.

120.
★ Final term Spring 2009

The shortest frame in HDLC protocol is usually the _________ frame.

  1. AInformation
  2. BSupervisory
  3. CManagement
  4. DNone of the given

Supervisory frames carry no information field, so they are usually the shortest.

121.
★ Final term Spring 2006

In a time-domain plot, the vertical axis is the measure of ________.

  1. AAmplitude
  2. BFrequency
  3. CPhase
  4. DTime

A time-domain plot shows amplitude on the vertical axis against time.

122.
★ Final term Spring 2006

Which topology requires a multipoint connection?

  1. AMesh
  2. BStar
  3. CBus
  4. DRing

All devices share one bus cable, a multipoint link.

123.
★ Final term Spring 2006

If the data unit is 111111, the divisor 1010, and the remainder 110, what is the dividend at the receiver?

  1. A111111011
  2. B111111110
  3. C1010110
  4. D110111111

The receiver gets the data followed by the CRC remainder: 111111 + 110 = 111111110.

124.
★ Final term Fall 2006

OSI standard is practically implemented in the form of internet.

  1. ATRUE
  2. BFALSE

The Internet is built on the TCP/IP suite, not the OSI model.

125.
★ Final term Fall 2006

TCP/IP application layers combine the functions of OSI Application, Session and Transport layers.

  1. ATRUE
  2. BFALSE

The TCP/IP application layer combines OSI application, presentation and session layers; transport stays separate.

126.
★ Final term Fall 2006

Unipolar uses one voltage level.

  1. ATRUE
  2. BFALSE

Unipolar encoding uses one nonzero voltage level, with zero for the other bit.

127.
★ Final term Fall 2006

The material of core and cladding in fiber optic cable is same.

  1. ATRUE
  2. BFALSE

Core and cladding have different densities (refractive indices) so light reflects at the boundary.

128.
★ Final term Fall 2006

Burst error is more easily corrected than bit error.

  1. ATRUE
  2. BFALSE

Burst errors change several bits, so they are harder to correct than single-bit errors.

129.
★ Final term Fall 2006

Set of rules governing communication is known as

  1. AOSI model
  2. BProtocol
  3. CMedium

A protocol is the set of rules that governs data communication.

130.
★ Final term Fall 2006

WDM (wave division multiplexing) deals with

  1. Aelectric waves
  2. Blight waves
  3. Cboth

WDM multiplexes light signals of different wavelengths on fiber.

131.
★ Final term Fall 2006

A null modem is a

  1. Atraditional modem
  2. Btechnique to connect two DTE
  3. Cboth

A null modem crosses interface lines to connect two DTEs directly without modems.

132.
★ Final term Fall 2006

Router works on

  1. Adata link layer
  2. Bphysical layer
  3. Cnetwork layer

Routers forward packets using network-layer addresses.

133.
★ Final term Fall 2006

Poll/Select is a technique related with

  1. Aline control
  2. Bline discipline
  3. Cerror control

Poll/select is the line discipline method for primary-secondary links.

134.
★ Final term Spring 2005

In cyclic redundancy checking, what is the CRC?

  1. Athe divisor
  2. Bthe quotient
  3. Cthe dividend
  4. Dthe remainder

The CRC is the remainder of the binary division appended to the data.

135.
★ Final term Spring 2005

In fiber optics the signal source is ____________ waves.

  1. ALight
  2. BRadio
  3. CVery Low frequency
  4. DInfrared

Optical fiber carries signals as light.

136.
★ Final term Spring 2005

Each device has a dedicated point-to-point line configuration only with the two devices on either side of it.

  1. ARing Topology
  2. BStar Topology
  3. CMesh Topology
  4. DTree Topology

In a ring each device links point-to-point only to its two neighbors.

137.
★ Final term Spring 2005

_______ measures the relative strengths of two signals.

  1. ADecibel
  2. BBandwidth
  3. CWavelength
  4. DPhase

The decibel expresses the ratio of two signal powers.

138.
★ Final term Spring 2005

Which multiplexing technique shifts each signal to a different carrier frequency?

  1. AFDM
  2. BSynchronous TDM
  3. CAsynchronous TDM
  4. DNone of the above

FDM modulates each signal onto its own carrier frequency.

139.
★ Final term Spring 2005

The _____________ of a signal is the width of the frequency spectrum.

  1. AAmplitude
  2. BBandwidth
  3. CBit interval
  4. DPhase

Bandwidth is the range (width) of frequencies a signal contains.

140.
★ Final term past paper

Ethernet LANs can support data rates between _____________.

  1. A1 and 100 Mbps
  2. B1 and 200 Mbps
  3. C1 and 500 Mbps
  4. D1 and 100 Gbps

The IEEE 802.3 family in the course spans 1 Mbps (1Base5) to 100 Mbps (Fast Ethernet).

141.
★ Final term past paper

Two devices have started their communications that are attached with each other through coaxial cable. What function will the coaxial cable perform here?

  1. AMedium
  2. BPath
  3. CLink
  4. DNode

The cable is the transmission medium carrying signals between the devices.

142.
★ Final term past paper

___________ protocols are used in shared point to point link.

  1. ADirect
  2. BIndirect
  3. CMonolithic
  4. DStructured

When entities share a point-to-point (or multipoint) link, they communicate with a direct protocol.

143.
★ Final term past paper

Standards restricted within an organization fall in the category of ___________ standards.

  1. ANon-Proprietary
  2. BDe-jure
  3. CProprietary
  4. DIEEE

Proprietary (closed) standards are owned by and restricted to one organization.

144.
★ Final term past paper

Protocol Data Unit (PDU) at network layer is specifically named as _________.

  1. ASegments
  2. BPackets
  3. CFrames
  4. DBits

The network-layer PDU is a packet.

145.
★ Final term past paper

EIA 449 uses __________ standards to define its electrical specifications.

  1. ARS-422, RS-423
  2. BRS-422, RS-532
  3. CRS-412, RS-333
  4. DRS-413, RS-321

EIA-449 uses RS-423 (unbalanced) and RS-422 (balanced) for its electrical specifications.

146.
★ Final term past paper

The speed of light is __________ in vacuum.

  1. A3 Km/s
  2. B300 Km/s
  3. C300,000 Km/s
  4. D300,00 Km/s

Light travels at about 3 x 10^8 m/s, i.e. 300,000 km/s.

147.
★ Final term past paper

___________ is popular for supporting higher bandwidth and higher data rate.

  1. ACoaxial Cable
  2. BOptical Fiber
  3. CSTP
  4. DUTP

Optical fiber offers far higher bandwidth and data rates than copper.

148.
★ Final term past paper

_________ is a technique which specifically works on light beams.

  1. AFDM
  2. BWDM
  3. CTDM
  4. DCDM

Wave-division multiplexing combines light beams of different wavelengths on a fiber.

149.
★ Final term past paper

CSMA/CD stands for ___________.

  1. ACarrier sense multiple access/collision detection
  2. BCollision sense multiple access/collision detection
  3. CCollision stop multiple access/collision detection
  4. DControl software multiple access/collision detection

CSMA/CD is carrier sense multiple access with collision detection.

150.
★ Final term past paper

________ is a bus topology LAN that uses baseband signaling and has a max. segment length of 500 meters.

  1. A10 Base5
  2. B10 Base2
  3. C100 Base2
  4. D100 BaseT

10Base5 (thick Ethernet) is a baseband bus with 500 m segments.

151.
★ Final term past paper

In FDDI, __________ passing is used as access method.

  1. ATicket
  2. BPacket
  3. CToken
  4. DFrame

FDDI uses token passing.

152.
★ Final term past paper

RARP stands for _____________.

  1. AReverse Address Revolution Protocol
  2. BReverse Address Resolution Protocol
  3. CReverse Address Routing Protocol
  4. DReverse Address Reverse Protocol

RARP is the Reverse Address Resolution Protocol.

153.
★ Final term past paper

In the process of CRC, _________ has no importance and is not attached with data at sender/receiver side.

  1. AQuotient
  2. BDivisor
  3. CDividend
  4. DRemainder

Only the remainder matters in CRC; the quotient is discarded.

154.
★ Final term past paper

At the CRC checker, ________ means that the data unit is not damaged.

  1. AAll 0s in remainder
  2. BA string of 1s in remainder
  3. CA string of alternating 1s and 0s in remainder
  4. DA nonzero remainder

A zero remainder at the checker means the data arrived intact.

155.
★ Final term past paper

At the beginning of transmission, the receiver window contains ________ spaces for frames in sliding window mechanism.

  1. An
  2. Bn-1
  3. Cn+1
  4. D1/n

With sequence numbers 0 to n-1 the window initially holds n-1 frames.

156.
★ Final term past paper

One Multistation Access Unit can support up to ____ stations.

  1. A6
  2. B7
  3. C8
  4. D9

A Token Ring MAU supports up to eight stations.

157.
★ Final term past paper

In fiber optics, signals are transmitted in the form of ____________.

  1. AAnalog
  2. BDigital
  3. CElectromagnetic
  4. DLight

Optical fiber carries signals as light.

158.
★ Final term past paper

BNC connectors are used by ___________ cables.

  1. AUTP
  2. BSTP
  3. CCoaxial
  4. DFiber

BNC (bayonet) connectors are used with coaxial cable.

159.
★ Final term past paper

________ measures the relative strength of two signals or a signal at two different points.

  1. ADecibel
  2. BData rate
  3. CBaud rate
  4. DFrequency

The decibel expresses the relative power of two signals or points.

160.
★ Final term past paper

The Hamming code is used for __________.

  1. AMultiplexing
  2. BDe-Multiplexing
  3. CEncryption of data
  4. DDetection and correction of errors

Hamming code detects and corrects single-bit errors.